AlumaSeal® 384™ and 96™ Aluminum Foil Seal

Easy-to-pierce Aluminum Foil Seal for Direct Sample Recovery.

AlumaSeal® 96™ provides a secure seal for 96-well raised-rim and non-skirted PCR plates to minimize evaporation, reduce cross-contamination and prevent spillage. 

• Certified DNase- & RNase- free
• Ideal for use with 384-well and deep-well plates (or select AlumaSeal® 96™ for smaller cut for raised-rim and non-skirted PCR plates.)
• Features one end-tab with no perforation
• Pierceable with a pipet tip or robotic probe for direct sample recovery
• Large cut allows for easier positioning of the foil to the plate via edge of plate alignment vs. centering
• Available in roll format for automation: AlumaSeal® Roll-Seal, 80 mm x 100 mm

• PCR
• Long-term storage
• Light sensitive assays
• Robotics

• -80°C to +120°C

• End-tab removal before thermal cycling is highly recommended
• Remove diagonally from a corner to prevent tearing
• Selection of the proper film size will minimize evaporation
• The film should not overhang or ride up the wall of a raised-rim plate
• More complete coverage of skirted flat-top plates will reduce evaporation in the outer wells

Designed to Facilitate Air and CO2 Exchange.

Designed to Facilitate Air and CO2 Exchange. AeraSeal™ features a hydrophobic, gas permeable membrane with a medical grade, non-cytotoxic adhesive. The porous membrane consists of layers of heat welded rayon fibers.

• Pore size from 10 uM to 50 uM
• Moisture vapor transmission rate = 4,200 g/m²/24 hr
• Easy-to-pierce with serological pipets and pipet tips for direct sample recovery
• Available in roll format for automation: AeraSeal™ Roll-Seal

SealPlate® SealMate™ Rolls

For Fast and Efficient Microplate Sealing. The SealMate SealPlate Starter Kit features a re-usable dispenser and two rolls of perforated film.
 
The dispenser facilitates the quick and easy dispensing of film from a roll allowing microplates to be sealed three times faster than using sheeted films. Cost-effective replacement rolls are sold separately. Ideal for use under the hood; the SealMate dispenser minimizes film contamination.

• Environmentally friendly; no paper liner to remove and discard; utilizes approximately 72% less material than SealPlate sheeted film
• Each sheet is separated by an adhesive-free, perforated, color-coded green band
• The smooth lower surface of the dispenser can be used to seal the film to the plate
• Dispenser protects unused seals from contamination
• Lower support prop prevents dispensing bill from contacting surfaces to prevent contamination
• Replacement rolls can be easily installed by releasing the locking clasps on the dispenser

• General laboratory use
• Short-term storage
• Incubation
• ELISA

• -40°C to +120°C

General Purpose Sealing Film

• Certified DNase- & RNase- free
• Features good chemical resistance
• Provides a very secure seal to minimize evaporation, but is slightly harder to remove than SealPlate films
• Less rigid polypropylene film reduces aerosols upon removal
• Specially formulated adhesive minimizes plate residue
• Can be used as a temporary seal while awaiting further processing

SealPlate® Sealing Film

Industry Standard for Sample Protection.
 
SealPlate® minimizes evaporation, prevents well-to-well contamination and spillage. Eliminates the “edge effect” which can occur with plate lids (e.g. greater evaporation in the outside plate wells).

• Provides a secure seal and is easy to remove
• Rigid polyester film features good clarity and easy handling
• Can be used as a temporary economical seal while awaiting further processing
• Features two end-tabs with perforations

AlumaSeal® II™ Easy-to-pierce Aluminum Foil Seal
 
Easy-to-pierce, Medical Grade Acrylic Adhesive. 

FoilSeal™

Click to shop new and improved eXTReme™ 2 Seal Extra Strong Sealing Film

eXTReme™ Seal Extra Strong Sealing Film

eXTReme™ Seal features an extra-strong thick adhesive to minimize evaporation, yet removes easily without leaving residue on the plate.

Features chamfered corners to eliminate plate overhang for robotics applications and tight storage conditions.

• Certified DNase- & RNase- free
• Ideal for use with raised-rim and non-skirted PCR plates
• Available in a larger cut for flat-top semi-skirted and full-skirted PCR plates: eXTReme™ Seal, Large

Application

• PCR
• Robotics

Helpful Tips

• Selection of the proper film size will minimize evaporation
• The film should not overhang or ride up the wall of a raised-rim plate
• More complete coverage of skirted flat-top plates will reduce evaporation in the outer wells
• End-tab removal before thermal cycling is highly recommended

Hoefer® Chroma Deluxe Dual Cool Vertical Protein Electrophoresis System

Ergonomic design offers easier handling and sample introduction.

• Maximum glass plate size 18 x 16 cm
• Gels are fully submerged for greater temperature equilibration
• Produces straight lanes and sharp, well-defined bands
• Run up to four gels (maximum 112 samples) at one time under identical conditions
• Accommodates denaturing and native polyacrylamide gels, and the second dimension of 2-D electrophoresis
• Run gels at uniform temperature from 1 to 45°C
• A wide array of accessories enables you to tailor gel configurations to your needs 

Hoefer® Chroma Deluxe Complete Unit (SE600X-15-15)

• Lower Buffer Chamber, 1/ea
• Upper Buffer Chamber, 1/ea
• Safety Lid w/High Voltage Leads, 1/ea
• Heat Exchanger, 1/ea
• Glass Plates 18 x 16 cm, 6/pk
• Clamp Assemblies, 16 cm, 4/pk
• Cams, 6/pk
• Slotted Gaskets for Upper Buffer Chamber, 2/pk
• Dual Gel Casting Stand with Leveling Base, 1/ea
• Bubble Level, 1/ea
• Laminated Gaskets for Caster, 2/pk
• Buffer Dam, 1/ea
• Spacer-Mate Alignment Template, 1/ea
• Wonder Wedge Plate Separation Tool, 1/ea
• Gel Seal, 1/ea
• Combs, 15-well, 1.5 mm thick, 2/pk
• Spacers, 1.5 mm thick, 2 cm wide, 4pk

Hoefer® Chroma Deluxe Basic Unit (SE600X)

The same as above without the combs and spacers. Order two SE511 combs and two sets of 16 cm long spacers separately.

Specifications
 

Plate Size (W x H)	7.09 x 6.30, or 7.09 x 3.15 In. 18 x 16 or 18 x 8 cm
Spacers	0.75 mm, 1.0 mm, 1.5 mm
Max. Power	1000 V, 500 mA, 50 W
Max. Temp.	113ºF | 45°C
Indoor Use	39.2 to 104ºF | 4 to 40°C
Humidity	Up to 80%
Dims (D x W x H)	5.51 x 12.60 x 11.42 In. | 14 x 32 x 29 cm
Weight	16.98 lb | 7.70 kg