Click to shop new and improved eXTReme™ 2 Seal Extra Strong Sealing Film

eXTReme™ Seal Extra Strong Sealing Film

eXTReme™ Seal features an extra-strong thick adhesive to minimize evaporation, yet removes easily without leaving residue on the plate.

Features chamfered corners to eliminate plate overhang for robotics applications and tight storage conditions.

• Certified DNase- & RNase- free
• Ideal for use with raised-rim and non-skirted PCR plates
• Available in a larger cut for flat-top semi-skirted and full-skirted PCR plates: eXTReme™ Seal, Large

Application

• PCR
• Robotics

Helpful Tips

• Selection of the proper film size will minimize evaporation
• The film should not overhang or ride up the wall of a raised-rim plate
• More complete coverage of skirted flat-top plates will reduce evaporation in the outer wells
• End-tab removal before thermal cycling is highly recommended

ILP Clear Zone™ and Indexed Sealing Film

• Pre-slit “x” wells allow for in-process access of wells without damage to film
• 2-end tabs and a white colored insert with 96 clear rings assist in film alignment
• Easy to peel 

Indexed Seal Pre-Slit Sealing Film

Clear, pre-slit, and printed wells; designed for in-process sample access.

Applications: Sample protection while processing, automation with pipette tips, and sample indexing

• Reduce pipetting errors with easy-to-read well indexing
• Ideal for protecting samples on the benchtop while working with the plate, especially for manual procedures
• Easy in-process access and well-indexed labeling 

Clear Zone™ Pre-Slit Sealing Film, 96 well PP

Clear with no adhesive over well areas and designed for in-process sample access with probes and reuse automation.

Applications: Sample protection while processing, autosamplers, automation with probes or needles

• Best choice for automation; Ideal for protecting samples while in process
• Adhesive-free well areas reduce potential contact with samples and the risk of fouling probes/needles 

Specifications
 

Item #	MID-SF061PP-SLT-PRT	MID-SF083PE-W-PRT	MID-SF063PP-SLT-CZ	MID-SF063PP-96-CZ
# of Plugs	96
Material	Polypropylene	PET	Polypropylene
Adhesive Material	Acrylic; 1.1 Mil
Liner Material	PET (polyethylene terephthalate)
Color	Clear	White	Clear
Alphanumeric	Printed
Certified	DNase-/RNase-/Pyrogen-Free
Overall Height	3.1 Mil	3.9 Mil	3.1 Mil	3.9 Mil
Adhesive Thickness	Acrylic; 1.1 Mil
Top Width	3.19 In. | 81.00 mm
Top Length	5.59 In. | 142.00mm
Autoclavable	No
Max Temp.	120ºC (248ºF)
Min Temp.	-40ºC (-40ºF)

 

ILP Aluminum Sealing Film

Soft and impermeable aluminum sealing foils with medical grade acrylic adhesive.  Once applied, the seal adheres aggressively, forming a tight positive seal preventing evaporation of VOCs, sample loss in storage, drying, cross contamination, and reducing the risk of aerosols and pathogens venting.

• Suitable for sealing all standard PCR plates, micro plates, and deep well blocks
• Perfect for light sensitive samples
• Easily pierced with single or multi-channel pipettors and probes
• Withstands long term storage down to -80°C
• Single tabbed backing paper removes easily; aluminum sheet resists rolling back

Specifications
 

Item #	MID-HSF50	MID-SF035AL
Material	Aluminum
Adhesive Material	Polypropylene	Acrylic; 1.1mil
Liner Material	No Liner	Polyester
Color	Silver
Alphanumeric	None
Surface Treatment	None
Certified	DNase-/RNase-/Pyrogen-Free
Overall Height	2.8 Mil	1.4 Mil
Top Width	3.27 In. | 83.00 mm
Top Length	4.92 In. | 125.00 mm	5.25 In. | 133.35 mm
Autoclavable	No
Max Temp.	100ºC (212ºF)	120ºC (248ºF)
Min Temp.	-80ºC (-112ºF)

 

ILP Polyester Sealing Film

Perfect for general sealing applications, prevention of cross-contamination, Elisa, incubation, and short-term storage. Our polyester films with acrylic adhesive are a great general-purpose seals, ideal for sample protection. The acrylic adhesive offers a strong bond that seals tightly on polypropylene and polystyrene plates.

The paper backing of this film is scored on both ends to allow for two-handed (precise) placement on the plate. MID-SF081-PE Films have writing tabs for clear identification.

Specifications

ILP Aerobic Seal Sealing Film

Non-woven Rayon, acrylic adhesive, breathable, 4.9 Mil – Sterile

Breathable sealing film made from non-woven rayon with an acrylic adhesive. Designed for aerobic applications, this 4.9 mil film allows gas exchange while maintaining a sterile barrier. Ideal for cell culture and other assays requiring ventilation.

Specifications
 

Material	Non-woven Rayon Acrylic
Adhesive Material	Acrylic; 1.1 Mil
Liner Material	Paper
Color	White
Alphanumeric	None
Certified	DNase-/RNase-/Pyrogen-Free
Overall Height	4.9 Mil
Adhesive Thickness	Acrylic; 1.1 Mil
Top Width	3.22 In. | 82.00 mm
Top Length	6.06 In. | 154.00 mm
Autoclavable	Pre-Sterilized
Max Temp.	80ºC (176ºF)
Min Temp.	-20ºC (-4ºF)

 

ILP Polyolefin Sealing Film 

• Optical Seal Adhesive Sealing Film
• Polyolefin 2.8 mil Ultra-clear for qPCR
• 50 Films/Pack, 10 Packs/Case 

Incredible optical clarity, non-absorbing, and non-fluorescing properties of these films make them ideally suited for Real Time PCR (qPCR) and optical assay work. Featuring an inert, ultra-clear, and strong encapsulated silicone adhesive that provides extraordinary performance in demanding applications.

Encapsulated silicone greatly reduces the risk of sample contamination due to exposure to adhesive. Once the film is pressed onto the plate, the raised portion of the well penetrates the encapsulation, and a tight seal is formed on just that surface (not over the sample). This silicone seal adheres aggressively, preventing evaporation and lessening the possibility of “Edge Effect”.

The plasticized backing of this film is scored on both ends to allow for two-handed (precise) placement on the plate. Both film and adhesive maintain incredible clarity and are the choice for highly demanding manual and automated processes.

Specifications
 

Material	PET (polyethylene terephthalate)
Adhesive Material	Encapsulated Silicone; 2.0 Mil
Liner Material	Polyester
Color	Clear
Alphanumeric	None
Surface Treatment	None
Certified	DNase-/RNase-/Pyrogen-Free
Overall Height	2.8 Mil
Overall Thickness	2.8 Mil
Adhesive Thickness	Encapsulated Silicone; 2.0 Mil
Top Width	3.06 In. | 77.80 mm
Top Length	5.56 In. | 141.27 mm
Autoclavable	No
Max Temp.	100ºC (212ºF)
Min Temp.	-70ºC (158ºF)

 

Hoefer® Chroma Deluxe Dual Cool Vertical Protein Electrophoresis System

Ergonomic design offers easier handling and sample introduction.

• Maximum glass plate size 18 x 16 cm
• Gels are fully submerged for greater temperature equilibration
• Produces straight lanes and sharp, well-defined bands
• Run up to four gels (maximum 112 samples) at one time under identical conditions
• Accommodates denaturing and native polyacrylamide gels, and the second dimension of 2-D electrophoresis
• Run gels at uniform temperature from 1 to 45°C
• A wide array of accessories enables you to tailor gel configurations to your needs 

Hoefer® Chroma Deluxe Complete Unit (SE600X-15-15)

• Lower Buffer Chamber, 1/ea
• Upper Buffer Chamber, 1/ea
• Safety Lid w/High Voltage Leads, 1/ea
• Heat Exchanger, 1/ea
• Glass Plates 18 x 16 cm, 6/pk
• Clamp Assemblies, 16 cm, 4/pk
• Cams, 6/pk
• Slotted Gaskets for Upper Buffer Chamber, 2/pk
• Dual Gel Casting Stand with Leveling Base, 1/ea
• Bubble Level, 1/ea
• Laminated Gaskets for Caster, 2/pk
• Buffer Dam, 1/ea
• Spacer-Mate Alignment Template, 1/ea
• Wonder Wedge Plate Separation Tool, 1/ea
• Gel Seal, 1/ea
• Combs, 15-well, 1.5 mm thick, 2/pk
• Spacers, 1.5 mm thick, 2 cm wide, 4pk

Hoefer® Chroma Deluxe Basic Unit (SE600X)

The same as above without the combs and spacers. Order two SE511 combs and two sets of 16 cm long spacers separately.

Specifications
 

Plate Size (W x H)	7.09 x 6.30, or 7.09 x 3.15 In. 18 x 16 or 18 x 8 cm
Spacers	0.75 mm, 1.0 mm, 1.5 mm
Max. Power	1000 V, 500 mA, 50 W
Max. Temp.	113ºF | 45°C
Indoor Use	39.2 to 104ºF | 4 to 40°C
Humidity	Up to 80%
Dims (D x W x H)	5.51 x 12.60 x 11.42 In. | 14 x 32 x 29 cm
Weight	16.98 lb | 7.70 kg

1 x 8 FilmStrips™

For Sealing Only One 8-well Row of a 96-well Plate.

Accuris MyVolt™ Mini Power Supply

• Compact and simple
• Choose constant 100 V or 200 V output
• Two pairs of output terminals 

The Accuris MyVolt™ Mini is a compact electrophoresis power supply ideal for basic, constant voltage applications. Users can select constant 100 V or 200 V output, and the current can reach a maximum of 200 mA.

Two sets of output jacks are available to connect up to 2 gel rigs and these small power supplies can securely be stacked for use with additional gel rigs.

Specifications

Hoefer® Tall Standard Dual Cool Vertical Protein Electrophoresis System

Taller vertical format accommodates 24 cm long gels for increased resolution.

• Maximum glass plate size 18 x 24 cm
• Produce straight lanes and sharp, well-defined bands
• Run up to four gels (maximum 112 samples) at one time under identical conditions
• Run gels at uniform temperature from 1 to 45°C
• Accommodates denaturing and native polyacrylamide gels and 2-D electrophoresis
• A wide array of accessories allows you to tailor gel configurations to your needs  

Hoefer® Tall Standard Complete Unit (SE660-15-15)

• Lower Buffer Chamber, 1/ea
• Upper Buffer Chamber, 1/ea
• Safety Lid w/High Voltage Leads, 1/ea
• Heat Exchanger, 1/ea
• Glass Plates 18 x 24 cm, 6/pk
• Clamp Assemblies, 8 cm, 4/pk
• Clamp Assemblies, 16 cm, 4/pk
• Cams, 6/pk
• Slotted Gaskets for Upper Buffer Chamber, 2/pk
• Dual Gel Casting Stand with Leveling Base, 1/ea
• Bubble Level, 1/ea
• Laminated Gaskets for Caster, 2/pk
• Buffer Dam, 1/ea
• Spacer-Mate-Alignment Template, 1/ea
• Wonder Wedge™-Plate Separation Tool, 1/ea
• Gel Seal, 1/ea
• Combs, 15-well, 1.5 mm thick, 2/pk
• Spacers, 1.5 mm thick (2 cm wide), 4/pk
• Lower Buffer Chamber, 1/ea 

Hoefer® Tall Standard Basic Unit (SE660)

The same as above without the combs and spacers. Order two SE511 combs and two sets of 24 cm long spacers separately.

Specifications
 

Plate Size (W x H)	7.09 x 9.45, 7.09 x 6.30, or 7.09 x 3.15 In. 18 x 24, 18 x 16 or 18 x 8 cm
Spacers	0.75 mm, 1.0 mm, 1.5 mm
Max. Power	1000 V, 500 mA, 50 W
Max. Temp.	113ºF | 45°C
Indoor Use	39.2 to 104ºF | 4 to 40°C
Humidity	Up to 80%
Dims (D x W x H)	5.51 x 12.60 x 14.57 In. | 14 x 32 x 37 cm
Weight	19.40 lb | 8.80 kg

Hoefer® Standard Dual Cooled Vertical Protein Electrophoresis System

Standard vertical format for 18 cm long gels.

• Maximum glass plate size 18 x 16 cm
• Produce straight lanes and sharp, well-defined bands
• Run up to four gels (maximum 112 samples) at one time under identical conditions
• Run gels at uniform temperature from 1 to 45°C
• Accommodates denaturing and native polyacrylamide gels and 2-D electrophoresis
• A wide array of accessories allows you to tailor gel configurations to your needs 

Hoefer® Standard Complete Unit (SE600-15-15)

• Lower Buffer Chamber, 1/ea
• Upper Buffer Chamber, 1/ea
• Safety Lid w/High Voltage Leads, 1/ea
• Heat Exchanger, 1/ea
• Glass Plates 18 x 16 cm, 6/pk
• Clamp Assemblies, 16 cm, 4/pk
• Cams, 6/pk
• Slotted Gaskets for Upper Buffer Chamber, 2/pk
• Dual Gel Casting Stand with Leveling Base, 1/ea
• Bubble Level, 1/ea
• Laminated Gaskets for Caster, 2/pk
• Buffer Dam, 1/ea
• Spacer-Mate Alignment Template, 1/ea
• Wonder Wedge Plate Separation Tool, 1/ea
• Gel Seal, 1/ea
• Combs, 15-well, 1.5 mm thick, 2/pk
• Spacers, 1.5 mm thick, 2 cm wide, 4/pk

Hoefer® Standard Basic Unit (SE600)

The same as above without the combs and spacers. Order two SE511 combs and two sets of 16 cm long spacers separately.

Specifications
 

Plate Size (W x H)	7.09 x 6.30, or 7.09 x 3.15 In. 18 x 16 or 18 x 8 cm
Spacers	0.75 mm, 1.0 mm, 1.5 mm
Max. Power	1000 V, 500 mA, 50 W
Max. Temp.	113ºF | 45°C
Indoor Use	39.2 to 104ºF | 4 to 40°C
Humidity	Up to 80%
Dims (D x W x H)	5.51 x 12.60 x 11.42 In. | 14 x 32 x 29 cm
Weight	15.43 lb | 7.00 kg