BrightMax™ White, Light-reflecting, Vinyl Sealing Film

Designed for use with white microplates.

• The light reflective properties on clear-bottom plates maximize the sensitivity of bioluminescence and chemiluminescence assays in bottom-reading luminometers
• Maximizes intensity and signal-to-noise ratios in luminescence assays
• May be used as a backing matrix for microscopy of punch-out samples for filter plates (e.g. ELISPOT assays)
• Features a single split liner for easy application

Applications

• Luminescence
• Fluorescence
• Microscopy

• -40°C to +80°C

TiterSeal™ Sealing Film

SealPlate® ColorTab™ Sealing Film for Sample Identification and Plate Labeling

An inscribed color-coded end-tab can be removed and pasted into a laboratory notebook while the other remains on the plate for identification. The film sheet can be removed from the plate without disturbing the identification label due to the finely perforated end-tabs. Choose from 5 different individual colors or the assortment pack.

• Provides a secure seal and is easy to remove
• Rigid polyester film features good clarity and easy handling
• Features two end-tabs with perforations

Applications

• General laboratory use
• Short-term storage
• Incubation
• ELISA

Temperature Range

• -40°C to +120°C

eXTReme™ FoilSeal™

EZcap™ PCR FilmStrips 

AlumaSeal® Easy-to-pierce Aluminum Foil Seal for Direct Sample Recovery
 
AlumaSeal® 384 provides a secure seal for 384-well plates to minimize evaporation, reduce cross-contamination and prevent spillage.

AlumaSeal® 96 provides a secure seal for 96-well raised-rim and non-skirted PCR plates to minimize evaporation, reduce cross-contamination and prevent spillage. 

• Certified DNase- & RNase- free
• Ideal for use with 384-well and deep-well plates (or select AlumaSeal® 96™ for smaller cut for raised-rim and non-skirted PCR plates.)
• Features one end-tab with no perforation
• Pierceable with a pipet tip or robotic probe for direct sample recovery
• Large cut allows for easier positioning of the foil to the plate via edge of plate alignment vs. centering
• Available in roll format for automation: AlumaSeal® Roll-Seal

• PCR
• Long-term storage
• Light sensitive assays
• Robotics

• -80°C to +120°C

• End-tab removal before thermal cycling is highly recommended
• Remove diagonally from a corner to prevent tearing
• Selection of the proper film size will minimize evaporation
• The film should not overhang or ride up the wall of a raised-rim plate
• More complete coverage of skirted flat-top plates will reduce evaporation in the outer wells

• Pore size from 10 µm to 50 µm
• Moisture vapor transmission rate = 4,200 g/m²/24 hr
• Easy-to-pierce with serological pipets and pipet tips for direct sample recovery
• Available in roll format for automation: AeraSeal™ Roll-Seal

SealPlate® SealMate™ Rolls for Fast and Efficient Microplate Sealing

The SealMate SealPlate Starter Kit features a re-usable dispenser and two rolls of perforated film.
 
The dispenser facilitates the quick and easy dispensing of film from a roll allowing microplates to be sealed three times faster than using sheeted films. Cost-effective replacement rolls are sold separately. Ideal for use under the hood; the SealMate dispenser minimizes film contamination.

• Environmentally friendly; no paper liner to remove and discard; utilizes approximately 72% less material than SealPlate sheeted film
• Each sheet is separated by an adhesive-free, perforated, color-coded green band
• The smooth lower surface of the dispenser can be used to seal the film to the plate
• Dispenser protects unused seals from contamination
• Lower support prop prevents dispensing bill from contacting surfaces to prevent contamination
• Replacement rolls can be easily installed by releasing the locking clasps on the dispenser

• General laboratory use
• Short-term storage
• Incubation
• ELISA

• -40°C to +120°C

Adhesive Sealing Film, Polyester, 3.1 mil