SealPlate® SealMate™ Rolls

For Fast and Efficient Microplate Sealing. The SealMate SealPlate Starter Kit features a re-usable dispenser and two rolls of perforated film.
 
The dispenser facilitates the quick and easy dispensing of film from a roll allowing microplates to be sealed three times faster than using sheeted films. Cost-effective replacement rolls are sold separately. Ideal for use under the hood; the SealMate dispenser minimizes film contamination.

• Environmentally friendly; no paper liner to remove and discard; utilizes approximately 72% less material than SealPlate sheeted film
• Each sheet is separated by an adhesive-free, perforated, color-coded green band
• The smooth lower surface of the dispenser can be used to seal the film to the plate
• Dispenser protects unused seals from contamination
• Lower support prop prevents dispensing bill from contacting surfaces to prevent contamination
• Replacement rolls can be easily installed by releasing the locking clasps on the dispenser

• General laboratory use
• Short-term storage
• Incubation
• ELISA

• -40°C to +120°C

General Purpose Sealing Film

• Certified DNase- & RNase- free
• Features good chemical resistance
• Provides a very secure seal to minimize evaporation, but is slightly harder to remove than SealPlate films
• Less rigid polypropylene film reduces aerosols upon removal
• Specially formulated adhesive minimizes plate residue
• Can be used as a temporary seal while awaiting further processing

SealPlate® Sealing Film

Industry Standard for Sample Protection.
 
SealPlate® minimizes evaporation, prevents well-to-well contamination and spillage. Eliminates the “edge effect” which can occur with plate lids (e.g. greater evaporation in the outside plate wells).

• Provides a secure seal and is easy to remove
• Rigid polyester film features good clarity and easy handling
• Can be used as a temporary economical seal while awaiting further processing
• Features two end-tabs with perforations

AlumaSeal® II™ Easy-to-pierce Aluminum Foil Seal
 
Easy-to-pierce, Medical Grade Acrylic Adhesive. 

FoilSeal™

Click to shop new and improved eXTReme™ 2 Seal Extra Strong Sealing Film

eXTReme™ Seal Extra Strong Sealing Film

eXTReme™ Seal features an extra-strong thick adhesive to minimize evaporation, yet removes easily without leaving residue on the plate.

Features chamfered corners to eliminate plate overhang for robotics applications and tight storage conditions.

• Certified DNase- & RNase- free
• Ideal for use with raised-rim and non-skirted PCR plates
• Available in a larger cut for flat-top semi-skirted and full-skirted PCR plates: eXTReme™ Seal, Large

Application

• PCR
• Robotics

Helpful Tips

• Selection of the proper film size will minimize evaporation
• The film should not overhang or ride up the wall of a raised-rim plate
• More complete coverage of skirted flat-top plates will reduce evaporation in the outer wells
• End-tab removal before thermal cycling is highly recommended

DuraSeal™ Sealing Film

• Durable, heat-resistant, solvent-proof laboratory sealing film
• Chemically resistant
• Heat resistant & Microwave compatible
• Tight sealing
• Tear resistant

DuraSeal™ is easy to use. There is no inter-leaf paper to strip away, just stretch the film symmetrically over a container opening and the 1.5 mil thick film contracts inwardly around the opening or neck of the container to provide a drum-tight, water-proof seal. The film can be elongated 500-800% before breakage. The film clings to itself, especially after stretching so the free edges of the film may be stretched around the container to secure the container edges.

Permeability Information

• Oxygen = 125cc/100in2/24hrs at 23°C
• Carbon Dioxide = 1300cc/100in2/24hrs at 23°C
• Water Vapor = 1.0g/100in2/24hrs at 38°C and 90% R.H.

ContainerSeal™ Sealing Tape

ContainerSeal™ is a sealing tape designed for the vast range of bottles and containers used in laboratory applications. Its unique elastomeric characteristics allow it to stretch and conform around the irregular perimeters of containers lids and covers to form a tight seal. ContainerSeal™ will block water vapor loss, reduce the rate of gas exchange and prevent the entry of contaminants and can be easily removed from most surfaces without leaving adhesive residue.

Specifications
 

Length	1,296 In. | 32.92 mm
Width	0.75 In. | 19.05
Color	Yellow
U of M	Roll

 

Proudly made in the USA! Click here for more made in America products! 
 

1 x 8 FilmStrips™

For Sealing Only One 8-well Row of a 96-well Plate.