Bullet Blender® Gold+ Homogenizers

Limited Time Promo!

2025 or while supplies last. All terms and conditions apply.

Bullet Blender® Gold+ Homogenizers

The Bullet Blender® Gold for tougher tissue/cell samples (mouse femur, tumor, and skin) now is dry ice compatible, eliminating sample heating during homogenization. All samples are automatically homogenized in the same manner, with high yields, so there is very little variation from sample to sample. There are no probes or blades to cause cross-contamination or sample loss, which also means there are no parts to clean between runs!

Available with CE certification
Made in the USA
Can be used in temperatures ranging from 4°C to 40°C. Altitude: < 2000 m
Storage Temperature: -40°C to 50°C

*avoid condensation, which will damage electronics and void the warranty

Bullet Blender® 50 Gold+ (BB50AUP)

Our largest dry-ice-cooled homogenizer. Can process tissue samples up to 3.5 g or cell culture combined with beads up to 20 mL. Process up to 4 tough tissue samples or up to 8 soft samples in 50 mL HIPPO™ tubes in parallel.

Includes

Pack of 20, 50 mL HIPPO™ tubes
2 Packs of 4 sleeves (8 sleeves in total)
Wholly scooper (to scoop dry pellets without the powder)
12V DC Wall Plug Power Cord
Basic Starter Kit:

Bead Sample Pack: 20 mL centrifuge tubes of 8 different types of beads
500 uL microspoon and 1.2 mL spoon

Bullet Blender® E5 Gold+ (BB5EAUP)

Homogenizer for tissue or cell cultures. Can process up to 12 samples in parallel, each sample up to 1 g each in a 5 mL GATOR™ tube or in *1.5 / 2 mL tubes using the tube adapters (purchased separately).

Includes

Pre-filled 5 mL GATOR™ snap cap tubes with beads, 3 each (Pink, Red, Green, and Navy)
25 Pack of 5 mL GATOR™ snap cap tubes
Wholly scooper (to scoop dry pellets without the powder)
24 V DC power supply
Basic Starter Kit:

Bead Sample Pack: 10 mL samples of 9 different bead types.

Bullet Blender® 24 Gold+ (BB24AUP)

Homogenizer for 24 0.3 g samples in microcentrifuge tubes with a very powerful motor. Used with 1.5 mL GATOR™ snap cap Tubes RINO™ screw cap tubes.

Includes

Contact plate for use with GATOR™ Tubes
40 Pack of 1.5 mL GATOR™ snap cap Tubes
Wholly scooper (to scoop dry ice pellets without the powder)
24 V DC power supply
Basic Starter Kit:

Bead Sample Pack: 5 mL samples of eight different bead types.
Pre-filled 1.5 mL RINO® tubes with beads, 4 each (Pink, Red, Green, Navy)
50 Pack of 1.5 mL RINO® screw-cap tubes

Proudly made in the USA! Click here for more made in America products!

Item#:

ASBBGOLDPLUS

Bead Lysis Kit Selection Sheet

Bullet Blender Selection Sheet

Bullet Blender® 50DX+

Extra-powerful Bullet Blender® 50DX homogenizes better and faster. Processes up to 4 tough tissue samples or up to 8 soft samples in parallel. Each sample can be up to 3.5 g of tissue or 3.5 mL of pelleted cells combined with a buffer of up to 20 mL. Use HIPPO™ brand 50 mL self standing tubes with plug seal cap.

Air cooling™ minimizes sample heat up. Updated touchscreens allow for easy use. CE certified.

Includes

20 Pack of 50 mL HIPPO™ tubes
2 Packs of 4 sleeves (8 sleeves in total)
12 V DC Wall Plug Power Cord
Basic Starter Kit:

Bead Sample Pack: 20 mL centrifuge tubes of 8 different types of beads
500 uL microspoon and 1.2 mL spoon

Proudly made in the USA! Click here for more made in America products!

Item#:

ASBB50DX

Bead Lysis Kit Selection Sheet

Bullet Blender Selection Sheet

Bullet Blender® Storm Pro Homogenizer

Limited Time Promo!

For a limited time, purchase select Bullet Blender Gold+ or Storm Pro Models
(Item # BB24AUP and BT24M) at a Discount, plus get two packs of
RINO Bullet Blender Navy Bead Lysis kits FREE (50 kits/pk)!
**(*Enter 2 Item # NAVYR1-RNA-VF to your cart for free bead kits)**

Free offer with purchase of designated items at the listed price. Cannot be combined with any other discounts or pricing offers.
Not valid on prior purchases. Special price applies only to the specified item; no substitutions.
Promo valid until 12/31/2025 or while supplies last. All terms and conditions apply.

Bullet Blender® Pro Homogenizers

Homogenize your toughest samples (mouse femur, skin, tumor, etc.) in just minutes. Air cooling™ minimizes sample heat up. Updated touchscreens allow for easy use. CE certified.

Bullet Blender® 5E Pro (BT5E)

Our most powerful homogenizer! Process up to 12 samples at a time in 5 mL GATOR™ tubes and * 1.5 / 2 mL Tubes w/ adapter. Great for tough samples up to 1 g in size.

Includes

24 V 3.75 amp DC Power Supply (UL / CE)
Power cord
Basic Starter Kit:

Bead Sample Pack: 10 mL samples of 9 different bead types
100 uL and 500 uL microspoons
Pre-filled 5 mL GATOR™ snap cap tubes with beads, 3 each (Pink, Red, Green, Navy)
25 Pack of 5 mL GATOR™ snap cap tubes

Bullet Blender® Storm Pro (BT24M)

Quickly homogenize up to 24 of your toughest samples. Uses 1.5 mL RINO® screw cap tubes or 1.5 mL GATOR™ snap cap tubes.

Includes

Contact plate for use with 1.5 mL GATOR™ snap cap tubes
40 Pack of 1.5 mL GATOR™ snap cap tubes
24 V 2.5 amp DC Power Supply (UL / CE)
Power cord
Basic Starter Kit:

Bead Sample Pack: 5 mL samples of 8 different bead types
100 uL microspoon
Pre-filled 1.5 mL RINO® tubes with beads, 4 each (Pink, Red, Green, Navy)
50 Pack of 1.5 mL RINO® screw cap tubes

Bullet Blender® Lite (BT12LT)

The all new Bullet Blender® Lite can homogenize up to 12 samples. Uses 1.5 mL GATOR™ snap cap tubes. Can accommodate 1.5 mL RINO® screw cap tubes *with the purchase of an adapter.

Includes

24 V 2.5 amp DC Power Supply (UL / CE)
Power cord
Basic Starter Kit:

Bead Sample Pack: 5 mL samples of 8 different bead types
100 uL microspoon
Pre-filled 1.5 mL GATOR™ snap cap tubes with beads, 4 each (Pink, Red, Green, Navy)
40 Pack of 1.5 mL GATOR™ snap cap tubes

Proudly made in the USA! Click here for more made in America products!

Item#:

ASBULLETSTORM

Bead Lysis Kit Selection Sheet

Bullet Blender Selection Sheet

Pulse 150™ Ultrasonic Homogenizer

Pulse 150™ Ultrasonic Homogenizer

Ideal for cell disruption, DNA shearing and ChIP assays
Programmable with touch screen control and pulsed operation
150 W, for volumes 0.1 to 150 mL (requires appropriate horn)

The Pulse 150 Ultrasonic Homogenizer uses cavitation and ultrasonic waves to break cells in suspension, shear DNA and prepare samples for ChIP assays. With up to 150 watts of power, the unit processes samples from 0.1 mL to 150 mL (with the appropriate horn).

All components needed for homogenization are included with the Pulse 150™ - a controller, transducer, temperature probe, 6 mm diameter titanium alloy horn and wrenches to change horns. A soundproof box with sample platform is also supplied as standard. The box reduces the noise generated by the sonicator. The 6 mm horn is appropriate for volumes from 10 mL to 100 mL.

Operating parameters are set and viewed on the 4.3 inch color touch screen. Pulsed operation is easily programmed as is the power level. Twenty programs can be stored in memory and recalled as needed. Alarms alert the user to over temperature, over/no load and expiration of time.

Item#:

ASPLUS150

Benchmark™ BeadBlaster™ 96 Ball Mill Homogenizer

Benchmark™ BeadBlaster™ 96 | Ball-Mill Homogenizer for Plates, Tubes and Jars

Wet, dry or cryogrinding
Accepts a variety of tubes, plates and jars
Large, digital touch screen control panel
See-though safety lid

The BeadBlaster™ 96 is an extremely versatile bead mill homogenizer that has applications in a variety of areas, including biological research, environmental testing, and industrial settings. Adapters are available for microplates, microtubes, and 50ml tubes. Grinding jars and balls in a variety of materials are available.

Wet homogenization, dry grinding and cryogrinding can all be performed with the BeadBlaster™ 96. The arced motion of the sample holders and powerful motor allow most samples to be processed in 1 minute or less. All parameters are digitally controlled through the large touch screen and 9 programs can be stored in memory.

The safety cover lifts up for easy access to the sample holders and automatically locks during operation. The wrap-around design of the clear acrylic lid allows for visualization during homogenization.

Specifications

Speed Range	180 to 1800 rpm
Speed Increment	100 rpm
Cycle Duration	1 sec to 59 min. 59 sec
Pause	1 sec to 59 min. 59 sec
Cycles	99
Programs	9
Dimensions (W x D x H)	13.19 x 19.68 x 14.37 In. 335 x 500 x 365 mm
Weight	141 lbs. \| 64 kg.
Electrical	120 V, 50 Hz
Warranty	2 years

Item#:

ASIPD9600

Prefilled Tubes & Bulk Beads Selection Chart

BeadBug™ 6 Homogenizer

The BeadBug™ is a high energy benchtop homogenizer that sets the performance standard for personal sized cell disruption and lysis instruments.

Simultaneous homogenization of up to 6 samples takes place (often within 45 seconds) inside the disposable 2 mL screw cap microtubes. The optimized mixing motion causes rapid cell disruption through constant high velocity impact from the hardened micro-beads chosen specifically
for your sample type.

Developed for samples too tough to be homogenized in a common lab vortexer, the BeadBug™ provides a convenient and economical alternative to the traditional, over-priced homogenizers on the market today. With up to six tube capacity and a footprint of just 9 x 14 in., the BeadBug™ is
the ideal homogenizing instrument for low to medium throughput laboratories.

Specifications

Speed Range	2500 to 4350 rpm
Capacity	6 x 2 mL or 2 x 5 mL (required optional adapter)
Cycle Time	1 to 90 sec. (up to 90 sec.)
Pause between cycles	0 to 90 sec. (1 sec. increments)
Max, cycles per program	10
Program Memory	up to 50
Noise Level	<65 db
Timer	1 sec to 90 sec with up to 10 cycles
Dimensions (D x W x H)	8.6 x 14 x 8 In. \| 22 x 35.5 x 20.5 cm
Weight	20 lbs \| 9 kg

Item#:

ASBEADBUG1

BeadBug™ Microtube Homogenizer

Powerful - for mixing, lysis, grinding or homogenization
Individual homogenization tubes - avoids cross contamination between samples
Multitask - homogenize 1-3 samples simultaneously

The BeadBug™ is a high energy benchtop homogenizer for individualized sample cell disruption to whole tissue homogenization. Simultaneous homogenization of up to 3 samples inside disposable 2 mL screw cap microtubes can be optimized for grinding for 3 seconds to 3 minutes. The mixing motion causes rapid disruption through constant high velocity impact from the hardened micro-beads chosen specifically for your sample type.

Developed for samples too tough to be homogenized in a common lab vortexer, the BeadBug™ provides a convenient and economical alternative to the traditional, over-priced homogenizers on the market today. With up to a 3 tube capacity and a tiny footprint of 7 x 8 in., the BeadBug™ is the ideal homogenizing instrument for low to medium throughput laboratories.

Specifications

Speed Range	2800-4000 rpm
Max. Capacity	3 x 2.0 mL (Non-Skirt)
Timer	3 sec. to 3 min.
Operating Temp. Range	+4°C to +65°C
Dimensions	6.9 x 8.3 x 5.3 in.
Weight	5 lbs.
Electrical	115 V,60 Hz or 230 V,50 Hz (add-E to item#)
Warranty	2 years

For best results, use with the BeadBug™ pre-filled tube kits: Includes 2.0 mL Non-Skirt Screw Cap tubes with caps, sealing rings and DNase/RNase-free beads as specified below:

D1032-SK	Triple-Pure Starter Kit, 10 each of 0.1, 0.5, 1.0, 1.5 and 3.0 mm
D1031-01	Prefilled 2.0 mL tubes, Silica (Glass) Beads, 0.1 mm Acid Washed
D1031-05	Prefilled 2.0 mL tubes, Silica (Glass) Beads, 0.5 mm Acid Washed
D1031-10	Prefilled 2.0 mL tubes, Silica (Glass) Beads, 1.0 mm Acid Washed
D1032-01	Prefilled 2.0 mL tubes, Zirconium Beads, 0.1 mm Triple-Pure - High Impact
D1032-05	Prefilled 2.0 mL tubes, Zirconium Beads, 0.5 mm Triple-Pure - High Impact
D1032-10	Prefilled 2.0 mL tubes, Zirconium Beads, 1.0 mm Triple-Pure - High Impact
D1032-15	Prefilled 2.0 mL tubes, Zirconium Beads, 1.5 mm Triple-Pure - High Impact
D1032-30	Prefilled 2.0 mL tubes, Zirconium Beads, 3.0 mm Triple-Pure - High Impact
D1033-28	Prefilled 2.0 mL tubes, Stainless Steel, 2.8 mm, Acid Washed

Item#:

ASBEADBUG

BeadBlaster™ 24 Tube Homogenizer

Beadblaster™ 24 Microtube Homogenizer

Fast, efficient homogenization in about 35 seconds
For all sample types, from soft tissue to bone
Mix up to 24 tubes simultaneously
Sealed 2.0 mL tubes-eliminates cross contamination

The Beadblaster™ 24 completely lyses, grinds, and homogenizes a broad variety of biological samples. Even the most difficult and resistant samples are fully homogenized, often in 35 seconds or less.

The stainless steel tube carrier subjects up to 24 samples to an optimized, high-speed, 3D motion, producing high energy impacts between the samples and microbeads that release cellular contents. After homogenization, samples can be centrifuged and the supernatant collected for further processing.

Operating parameters for the Beadblaster™ 24 are set and displayed digitally. To protect fragile, heat-sensitive samples, the unit can be programmed to operate in shortened consecutive cycles with a rest period in between. Up to 50 such programs can be stored in memory and recalled for future use. A transparent lid allows for visualization of samples and features a mechanical lid lock that prevents opening when the Beadblaster™ 24 is in operation. A brushless motor reduces motor noise and provides maintenance-free operation. See below for kits for use with the Beadblaster™ 24.

Specifications

Item #	D2400	D2400-R
Speed Range	4.0 to 7.0 m/s (0.05 m/s increments)
Capacity	24 x 2.0 mL
Cycle time	1 to 90 sec
Pause between cycles	0 to 2 min. (1 sec. increments)
Max cycles per program	10
Program Memories	up to 50
Accel./Decel. Time	<2 sec./<2 sec.	<4 sec./<4 sec.
Cooling Method	N/A	Compressor
Temperature Range	Ambient	-10°C
Precool Ambient to 0°C	N/A	<30 min
Chamber Uniformity	N/A	±2°C
Noise Level	<68 db	<65 db
Dimensions	28x36x38.5 cm	32 x 51 x 41 cm
Weight	55 lbs \| 25 kg	88 lbs \| 40 kg
Electrical	100 to 240 V, 50-60 Hz
Power	600 W	1,000 W
Warranty	2 years

Item#:

ASBEADBAST24

D1000 Handheld Homogenizer

Homogenize most samples in under 30 seconds
For volumes from 100 uL to 250 mL
Supplied with both 5 mm & 7 mm generator probes

The D1000 is designed to rapidly homogenize, emulsify, suspend and disrupt biological samples. Ideal for use with microtubes, the homogenizer works well with samples from 0.1 mL to 250 mL (depending upon the generator probe used).

The D1000 is a rotor stator homogenizer, and works by drawing the sample, in liquid into the generator probe with the variable speed rotor, and then forcing it out through the slots in the stator. This achieves mechanical shearing of the sample. As the sample is repeatedly drawn up and forced through the stator, additional shearing takes place. Most samples are completely homogenized in 30 seconds or less. A powerful, 130 W motor drives the rotor at speeds from 8,500 to 30,000 rpm. Speed is adjustable in six steps to meet sample processing needs. A separate on/off switch allows the homogenizer to be left at the appropriate setting.

Generator probes are available in four sizes. The 5 mm and 7 mm diameter have a 50 mm length for use with samples in microtubes. The 10 mm x 115 mm is ideal for use with 15 and 50 mL tubes and 14 mm x 130 mm, for 50 mL tubes and vessels up to 250 mL. The unit is supplied with one each of the 5 mm and 7 mm generator probes. All the generator probes are made of stainless steel and can be sterilized by autoclaving.

Sepcificactions

Speed Range	8,500 to 30,000 rpm
Capacity	0.1 mL to 250 mL
Noise Level	< 70 db
Operating Temperature Range	4°C to 65°C
Dims w/o generator (D x W x H)	1.8 x 2.3 x 9 In. \| 45.72 x 58.42 x 228.6 mm
Weight	1.35 lbs. \| 0.6 kg.
Electrical	115 V (60 Hz) or 230 V (50 Hz)
Warranty	2-yr

D1000	D1000 Handheld Homogenizer, includes D1000-M5 & D1000-M7
D1000-M10	10 mm x 115 mm Saw Tooth Generator Probe (for 15 mL and 50 mL tubes)
D1000-M14	14 mm x 130 mm Saw Tooth Generator Probe (for 50 mL to 250 mL vessels)
D1000-M5	5 mm x 50 mm Flat Bottom Generator Probe, 5/pk (for microtubes)
D1000-M7	7 mm x 50 mm Saw Tooth Generator Probe, 5/pk (for microtubes)
D1000-ST	Stand for D1000 Handheld Homogenizer

Item#:

ASHOMHD3

PRO Scientific Bio-Gen PRO200 Homogenizer

The PRO Scientific Bio-Gen PRO200 Homogenizer is a compact, handheld solution for precise and efficient sample processing. Built with a lightweight ergonomic design and a 144-watt high-torque motor, this homogenizer delivers variable speeds from 5,000 to 35,000 rpm, making it ideal for tubes and small beakers. For continuous operation, it includes a separate on/off switch and can be mounted on an optional stand assembly (sold separately).

The PRO200 is ideal for cell disruption, tissue homogenization, liquid emulsions, and small solid sample processing. It can break down samples to nanoparticle levels as small as 1 micron, ensuring consistent results for research and laboratory applications. Built in the USA and backed by a 2-year warranty, the PRO200 combines durability, precision, and ease of use for everyday lab needs.

Main Attributes

Compact, easy-to-use design for reliable sample preparation
Variable speed control: 5,000 to 35,000 rpm
Processes samples from 0.03 mL to 500 mL with consistency
Handheld or stand-mounted operation
Made in the USA
2-year warranty

Generator Probes (sold separately)

Choose the right probe for your application. Standard quick-connect probes are crafted from 316 stainless steel and PTFE for durability. The flat-bottom probe is perfect for micro-tubes, while the saw-tooth probe provides high shear force for samples from micro-tubes to small beakers. For multiple sample processing, the Multi-Gen 7XL Probes offer cost-effective, repeatable homogenization without cross-contamination.

PRO Scientific Generator Probes

Stand Assembly (sold separately)

Used for Bio-Gen PRO200 Homogenizer
Great small footprint of 8 x 7 In.
Includes Post, Cross Rod, Clamp, and Flat Base

* Sample piece size and quantity will affect breakdown. Sample solid piece size should not be larger than the diameter of the generator probe. For the most efficient homogenization of solids, the sample diameter of the largest solid should not be larger than the probe diameter.

Proudly made in the USA! Click here for more made in America products!

Item#:

ASPRO200HOM

PRO Scientific PRO250 Homogenizer

The PRO Scientific PRO250 Homogenizer delivers powerful, durable performance for a wide range of sample sizes. Combining a lightweight, ergonomic design with a 3/4 HP, 576-watt motor, this homogenizer offers variable speeds from 5,000 to 30,000 rpm, making it ideal for both handheld and stand-mounted applications.

Main Attributes

Processes samples from 0.05 mL to 5 L
Variable speed control: 5,000 to 30,000 rpm
Overload and overheat sensors for safety
Compatible with 5 mm to 30 mm generator probes (sold separately)
Handheld or stand-mounted operation
Made in the USA
2-year warranty

The PRO250 is perfect for cell disruption, tissue homogenization, liquid emulsions, and nanoparticle-level sample breakdown (as small as 1 micron). Built with precision in small-batch production and tested for quality, PRO homogenizers maintain a failure rate of less than 1%. For viscous samples, adding a Deflector Head to your probe improves sample movement and maximizes homogenization efficiency.

Generator Probes (sold separately)

Choose the right probe for your application. Standard quick-connect probes are crafted from 316 stainless steel and PTFE for durability. The flat-bottom probe is perfect for micro-tubes, while the saw-tooth probe provides high shear force for samples from micro-tubes to small beakers. For multiple sample processing, the Multi-Gen 7XL Probes offer cost-effective, repeatable homogenization without cross-contamination.

PRO Scientific Generator Probes

Stand Assembly (sold separately)

Used for Bio-Gen PRO250 Homogenizer
Great small footprint of 9 x 7 In.
Includes Post, Cross Rod, Clamp, and Flat Base

Proudly made in the USA! Click here for more made in America products!

Item#:

ASHOMHD5

PRO Scientific PRO25D Digital Homogenizer

The PRO Scientific PRO25D Digital Homogenizer is a compact yet powerful solution for precise sample processing. Featuring a bright LED display and user-friendly digital controls, this homogenizer allows you to fine-tune speeds from 0 to 30,000 RPM, ensuring accurate and consistent results across a wide range of applications.

Main Attributes

Processes volumes from 0.05 mL to 3.5 L*
Digital speed control with LED display for precision
Ideal for homogenizing, emulsifying, blending, and mixing
Includes U-shape stand assembly for stability
Made in the USA
2-year warranty

The PRO25D is perfect for cell disruption, protein extraction, emulsions, suspensions, medical research, and pharmaceutical processing. Compatible with PRO generator probes (5 mm to 30 mm), this homogenizer can break down samples to nanoparticle levels as small as 1 micron. Built in small-batch production with rigorous testing, PRO homogenizers maintain a failure rate of less than 1%.

Generator Probes (sold separately)

Choose the right probe for your application. Standard quick-connect probes are crafted from 316 stainless steel and PTFE for durability. The flat-bottom probe is perfect for micro-tubes, while the saw-tooth probe provides high shear force for samples from micro-tubes to small beakers. For multiple sample processing, the Multi-Gen 7XL Probes offer cost-effective, repeatable homogenization without cross-contamination.

PRO Scientific Generator Probes

*Viscous samples will reduce max capacity. Adding a Deflector Head to your Probe will facilitate movement of your sample during homogenization and help increase max volume homogenization.

*Higher volumes depend on sample viscosity.

Proudly made in the USA! Click here for more made in America products!

Item#:

ASPRO25DHOM